COPY RIGHTS : TO AVOID COPYRIGHT VIOLATIONS, ALL POSTS ARE SHOWN ALONG WITH SOURCES FROM WHERE ITS TAKEN. PLEASE CONTACT ME IN MY EMAIL SALEEMASRAF@GMAIL.COM , IF YOU ARE THE AUTHOR AND YOUR NAME IS NOT DISPLAYED IN THE ARTICLE.THE UNINTENTIONAL LAPSE ON MY PART WILL BE IMMEDIATELY CORRECTED.

I HAVE SHARED ALL MY PRACTICAL WATER TREATMENT EXPERIENCES WITH SOLVED EXAMPLE HERE SO THAT ANYBODY CAN USE IT.

SEARCH THIS BLOG BELOW FOR ENVO ,COMPACT STP,ETP,STP,FMR,MBBR,SAFF,IRON,ARSENIC,FLUORIDE,FILTER,RO,UASB,BIO GAS,AERATION TANK,SETTLING TANK,DOSING,AMC.

SEARCH THIS BLOG

Wednesday, September 28, 2016

How to make your own HOME COMPOSTER FOR FOOD WASTE FROM KITCHEN

How to make your own HOME COMPOSTER FOR FOOD WASTE FROM KITCHEN
 Inputs:
Do Compost: ∙ Vegetable Scraps ∙ Fruit rinds, cores, pits and peels ∙ Coffee grounds and filters ∙ Tea bags and loose leaf tea ∙ Pasta, breads, cereals, grains ∙ Paper napkins, towels ∙ Egg shells
 Do Not Compost: ∙ Meat ∙ Fish and poultry ∙ Bones ∙ Oily foods ∙ Cheese ∙ Butter and dairy products ∙ Other animal products
Process:
Waste is collected and brought to the site where it is first sorted out and shredded to a consistent size. cut everything down to 1.5" size It is than put inside the composter.
One of the easiest ways to compost non-meat food waste is using a garbage can sunk in the ground. You can use an old or new can, but it should have a tight-fitting lid. Galvanized metal cans work well and do not rust. Volume as per capacity. Drill or punch about 30 drain holes, 1/4 to 3/8 inches in diameter, in the can bottom and around the lower sides. If the lid is not tight-fitting or if you do not have a lid, you can make a lid from a piece of plywood and strap it on with bungee cords. Dig a hole  in a well-drained corner of your yard and set the can into the hole, pushing soil around the sides to firmly plant the can (see our drawing). You’re ready to compost!
Composting To compost, put vegetable-based food scraps in your can, alternately layering with some dry leaves, sawdust, or shredded newspaper. The texture of the finished compost will depend on the materials composted and how long they spend in the can, and may range from a wet slurry to a dark, crumbly substance similar to soil. Depending on your food habits, your composter will likely fill in four to eight months
Harvesting the Compost To harvest, shovel the top layer of un-composted food to one side and shovel the dark, soil-like compost from the bottom. Finished compost should be dry and sweet smelling; if it is wet and smelly, mix it with some soil before using. In the meantime, make room for more food scraps in the can by replacing the layer of un-composted food in the can or burying it in a trench in the garden. Or, set up a second can. Use one until full and then switch to the second, switching any un-composted food scraps between the two. Using Finished Compost The most common uses of compost are as a soil enhancer for planting.
How to make or get accelerators or Bio cultures?
Bio cultures are required with cooked foods it is necessary to accelerate the decomposition.
WE SUPPLY THIS BIO CULTURE

HOW IT WORKS:
Carbon/Nitrogen Ratio: = 30:1
This is the first law one has to adhere to in order to ensure
rapid composting. Every ingredient you add into your
composter has it's own inherent C/N ratio, like
·         Grass clipping         = 15:1
·         Soft wood chips      = 226:1
·         Vegetable Waste     = 11:1
·         Poultry Manure       = 10:1

What you decide put into your composter the first day is the
weighted average of each of the individual items' C/N Ratio.
My ingredients, for example, are predominantly Grass Clippings
and Soft wood chips and I have computed my ratio to be 3 parts
grass clippings and 2 parts soft wood chips. You have to
perform the same calculation as I have, in order to arrive at
your final predominant ingredient ratio
.
Note: Remember to cut everything down to 1.5" size.

Water
A 50% water content is necessary. This means the composter
may have to be watered from time to time if it appears dry and
the side vents will have to be left open if it appears wet. 50%
water content is as wet as a wrung out sponge. If you see
water settling on the bottom, it is too wet.


After the 3rd day of composting, when the waste (future
compost) has gone down to half it's original volume, the 55
Gallon drum is now only 1/2 full. This amount is below it's
critical mass and will loose heat at night when it the ambient is
cooler. This way you will loose 8 hours of valuable composting
time cutting into your 17 day harvest cycle. What I do is place a
20mil plastic sheet over the waste in order to insulate the
material and speed up the process.

Aeration
Turn the barrel at least once every day. If you do that, the
entire process will take 2.5 weeks, or 17 days. If you turn every
other day and all other conditions are correct, the process will
take 25 days. Quite an amazing feat, considering a left alone
compost pile will take a whole year to mature.

Fine Tuning
If  you keep to the turning/tumbling schedule, one of 3 things
can go wrong and needs to be rectified mid-course.
·         Add/subtract Water.
·         Add Carbon rich ingredient (High C/N Ratio).
·         Add Nitrogen Rich ingredient (Low C/N Ratio).

As long as the ingredients are moist, a pile not heating up over
120˚F indicates not enough nitrogen, while one that smells bad
indicates not enough carbon. Either condition can be
corrected by adding the required ingredient.

Note: Never add anything else, mid course, or your 17 day
timetable will be altered.

COMPOST
The end product is this sweet smelling black gold that has to be sun
dried for a day or two (10% moisture content) and stored or
used immediately in your garden.
One Ton of BMW will produce approx. 500 KG of compost

Issue

Nothing is
happening. Barrel
doesn't seem to be
heating up at all.
Cause

- Not enough nitrogen
- Not enough oxygen
- Not enough moisture
- Compost is finished.
Resolution

- Make sure you have
enough nitrogen rich
sources like manure,
grass clippings or food
scraps.
- Rotate the Barrel
- A completely dry pile
doesn't compost


Read More : www.facebook.com/envoprojects
CONTACT US ENVO PROJECTS Mobile: 09899300371(Whatsapp)


Monday, September 26, 2016

ENVO COMPACT MBBR STP sewage treatment plant

THE ENVO COMPACT MBBR STP
STP FLOW CHART


                              PLEASE WATCH THE VIDEO

ENVO IS WORKING IN THIS FIELD SINCE 1994. 

An introduction to MBBR (moving bed biofilm reactor )/ FM Reactor/ FAB /FMR Reactor sewage treatment plant (STP)

THIS PLANT IS USED TO TREAT DIRTY WASTE WATER COMING OUT FROM ANY PLACE BEFORE RELEASING IT TO DRAIN. GOVERNMENT DOES NOT ALLOW UNTREATED DIRTY WASTE WATER TO BE RELEASED TO DRAIN DIRECTLY WITHOUT TREATMENT, IT IS CALLED WATER POLLUTION.

WHERE THIS PLANT IS REQUIRED
   1. Land development-housing colony, hotels,Restaurants, resorts, office      complexes,Multistory Buildings, Malls
   2  Schools,College, Hostel, Hospitals,Nursing Home, 
   3.Parks, other recreational areas
   4.  Rail Station,Public places 
   5.Biological treatment for industrial effluent

CHARACTERISTICS OF DIRTY WASTE WATER COMING TO STP:
pH --8
TSS--300 ppm
Oil & Grease --50 ppm
BOD--250 ppm
COD 650 ppm

CHARACTERISTIC OF TREATED WATER GOING OUT OF STP TO DRAIN

pH --8
TSS--less than 100ppm
Oil & Grease --less than 10 ppm
BOD--less than 30 ppm
COD less than 250 ppm

ENVO COMPACT MBBR STP  is a complete unit, pre-piped, pre-wired and ready to install. Engineered to serve with minimal maintenance, and designed to meet the requirements of the state water quality agency. Epoxy or other chemically resistant coatings, together with dependable accessory equipment assure long life and low maintenance cost. And the best part is the resale value. These total units can be re-located to serve again.




Features of COMPACT STP

o   Pre-engineered and prefabricated structure
o   Easily transported to the site
o   Modular design allows easy installation
o   Simple operation-less manpower required
o   User friendly-low maintenance
o   Long service life,
o   Custom designed
o   Efficient process, REDUCES BOD LOAD BY MORE THAN 80%
o   World-class finishing
o   Sludgecan be used as manure for horticulture purpose
o   Branded electrical/mechanical equipments used
o   Good resale value


The Process of Treatment

Primary Treatment (DEWATS/Collection tank before COMPACT MBBR)
In primary treatment, floating and suspended solids are settled and removed from sewage by bar screen. Following this, discharge from the sewers enters a DEWATS/collection chamber .

Secondary Treatment (COMPACT MBBR )
This is the next level treatment where the bacteria in sewage are used for further purification of the sewage. It’s a biological process that removes about 85% or more of the organic matter in sewage compared with primary treatment, where the purification level is about 50%. These processes are variations of what is called the "Activated Sludge" process, which provide a mechanism for bacteria, with air added for oxygen, to come in contact with the wastewater to purify it.

In the activated sludge process, flow from the sewer goes into the reactor, where compressed air is mixed with sludge in the presence of synthetic media on which the purifying organisms grow and contact the wastewater, removing contaminants in the process. The activated sludge allows bacteria to feed on the "food" provided by the new wastewater in the reactor, thus purifying it.

The flow, along with excess organisms that build up on the media during the purification, then goes to a Tube Settler. Air flows up through the media in the filters, to provide necessary oxygen for the bacteria organisms. Clarified effluent flows to the receiving water, typically a river , after disinfection. Excess sludge is produced by the process and after collection from the bottom of the tube settler it is dewatered, sometimes after mixing with primary sludge, for use as fertilizer, disposed of in a landfill, or incinerated.

Tertiary Treatment
Advanced level of water treatment is called tertiary treatment of water - where heavy metals, toxic chemicals and other pollutants are removed from wastewater to an altering degree. The tertiary treatment methods include micro filtration, carbon adsorption, evaporation/distillation, and chemical precipitation.

Civil Works:1.DEWATS(Collection tank),2..SDB,3.Treated water tank 4.Foundation for compact

SPECIAL FEATURE OF OUR DESIGN:
We provide two-stage treatment. DEWATS is the first stage treatment. Because of DEWATS, the blower capacity is reduced in the second stage of MBBR treatment thereby reducing the maintenance cost during running of the STP..

Electro Mechanical Components Involved COMPACT MBBR STP

Bio Reactor (MBBR) Double stage
Tube Settler
Raw sewage Pump
Air Blower ,Rotary type
Filter feed Pump
Sludge Pump
Dual media Filter
Activated Carbon Filter
Electrical Items
Pipe & Fittings
Erection commissioning of the system

         
The Treated water can be reused for horticulture, road washing etc without any further treatment.

ENVO PROJECTS ,NEW DELHI, 09899300371, 08076071358




Sunday, September 25, 2016

How to Become a Self Made Digital Marketing Expert


How to Become a Self Made Digital Marketing Expert 

Self learning is the best. 70% of the practical knowledge I have today is from my own projects. You should learn digital marketing from various sources available and apply some of it to your own projects.Anyone can get knowledge from Google and Wikipedia within 5 minutes.


You can keep scaling up with your own business and use the expertise to make profits. Good Digital Marketers will never prefer working for any company as a employee they would them self love to work as a consultant or may also build good Advertising Agency.It is the best working from home profession.Our sisters can do it very easily from home. The best way to become a digital marketing expert is to start practising digital marketing from today. The best thing about digital marketing is that you can start doing it at a very small scale. All you need is a computer, an internet connection and a small amount time. You can learn digital marketing by applying the concepts in your own mini-project. 

Here are the things you can do right now:

STEP ONE:: Choose a topic you are passionate about and start a blog (www.blogger.com) about it. Your BLOG is the main thing.The next thing is how to market your blog through various means.

STEP TWO: Learn a little about SEO and write SEO optimized articles in your blog. REGULARLY Write more articles of your interest and publish on your blog regularly.If you are taking others articles and posting it on your blog, always give the URL of the source article to avoid copyright violation.

STEP THREE :: Open an Adwords account on the blog
STEP FOUR: Sign up for Google Adsense and deploy advertising codes in your blog. 

STEP FIVE: Open a Facebook page dedicated to your blog (apart from your personal page) and invite your friends to your facebook page. Now,share the url of articles of your blog on your Facebook page.Make use of # and @ features of facebook in all your facebook updates. Be active in Facebook with regular posting of updates and reply to comments.Share the updates of others (influencers in your industry).Comment and like on others post (influencers in your industry).

STEP SIX: join Facebook Groups (Related to your business and your industry).Now, Promote the url of your facebook page in these Facebook groups

STEP SEVEN:: Create LinkedIn Profile. And  Join other groups (Related to your business and your industry) and actively post your facebook page in these groups.

STEP EIGHT:: Promote your url of your facebook page through email marketing .


Instead of sending out useful content to the email subscribers, you can publish that content on the blog and than on facebook page and email your subscribers a link to that facebook page. When subscribers visit that  article , they are very likely to share it on social media and check out your products/services again. Also this piece of content on the blog has the potential to attract new visitors from search and social media and those visitors may become subscribers as well.
Email Marketing Tips
§  Optimize lead generation on your content delivery channels. A lot of tools are available in the market place which helps you collect leads through blogs, videos and so on. 
§  Use DRIP email marketing. Drip email marketing is widely used because it completely automates the drip marketing process at a very low cost.
Once setup, no human intervention is needed. Drip emails designed for the purpose of lead nurturing perform better than other types of emails. http://digitaldeepak.com/drip-marketing/
Use tools such as Aweber, MailChimp, GetResponse to automate your drip email marketing process. Amazon SES and SendGrid are good email sending servers for the technically inclined.
§  Send a mix of marketing messages and valuable content. A good balance depends on the tolerance level of your market. Test, test, test.
  • All the sales I have got so far is by connecting with key people.
  • Mostly my email reaches the CEO or VP  of the company.
Key decision makers for digital marketing usually include:
● Founder
● Co-Founder
● CEO
● Chairman/Director 
● Head of Digital Marketing
● VP of Digital marketing
● VP of Marketing
● Head of Sales & Marketing
● Digital Marketing Managers

You can easily find this out by browsing on LinkedIn. First prepare the list of names. Then try to get their contact details.

This is your target market. These are your customers.Now that you have identified the target market, the next step is to reach them.

You can reach them via various methods:
● Email
● LinkedIn Message
●  Facebook Message

You first have to build a relationship and show them how they can benefit from you. It is always about what they can get from you than what you can get from them. 

HOW SHOULD BE YOUR EMAIL SUBJECT LINE ?

So let’s say you send them 2 emails with the subject lines:
1. “Looking for a job in digital marketing in your company”
2. “How your website - abcxyz.com can get more traffic via SEO”

The first email that you send will be deleted even without opening it.
But the second email will interest someone .

Track your Digital Marketing Activity – Important!!!You can track your marketing activity by doing the following steps:1)      Create a Google Analytics account,2)Add your website into Google Analytics, 3) Create all links to your website by using Google URL Builder (while creating URL Provide the source, Campaign Medium, Campaign Name etc.), 4) See the unique visitors and conversion (how many users are converted to sale).As long as you do the above listed activities, you will continue to see a high growth in your overall traffic. 
Start your activity now and see the change after 30 days !!!All the above steps can be done in 30 days by investing one hour per day. 

AS YOUR FIRST PROJECT, YOU CAN TRY MARKETING MY PRODUCTS & START EARNING FROM ME IMMEDIATELY FOR EACH SELL THROUGH YOUR EFFORTS.

Want to Reach Me? Email to: saleemasraf@gmail.com

INBOX ME AT  https://www.facebook.com/saleem.asraf